Description
TOYOTA / LEXUS key programmer with key emulator function
Supported models:
Cars with the KEYLESS-GO system, produced from 2008 to 03/01/2017
Operating principle:
The device receives data from the SMART module and emulates a key card to check the system performance with the following types of transponders 94 / D4 / 98/88 / A8 / A9. The device also allows you to add a new key.
Device appearance:
After connecting the device to OBD, you will see a menu with available functions.
Device control:
Use the UP and DOWN buttons to select the required action.
Confirm the action with the ENTER button or mark with the CANCEL button.
Description of functions:
CHECK – testing the function of disarming via the CAN bus.
CONNECTION – testing the engine start function. ADD – the function of adding an additional key. Previously recorded keys are not deleted.
3.0 – current version of the program
Equipment
Key Programmer
OBD cable
NEEDLES cable for connection to CAN bus
If the SMART module is not supported, you will see the message “LEARNING …”, wait about 1-2 minutes while the device analyzes the received data. Subsequent connections to this SMART module will not teach, the device will work instantly.
CHECK (disarming test function) This function is needed for CAMRY, PRADO, AVENSIS.
Connect the diagnostic cable to the device
Connect the device to the OBD diagnostic socket at the driver’s feet
Press and release the START / STOP button or press and release the brake pedal to “wake up” the car electronics
In the device menu, select CHECK
The doors will be unlocked and you will see the message OK !!!
Then execute the CONNECT function
CONNECTION (engine start test function)
Connect the diagnostic cable to the device
Connect the device to the OBD diagnostic socket at the driver’s feet
Press and release the START / STOP button or press and release the brake pedal to “wake up” the car electronics
In the device menu, select CONNECTION
If you see TRAINING … wait until the training is over, about 1-2 minutes
If you see RISE TO BUTTON – press and hold the brake pedal, touch the device to the START / STOP button, with the back cover as marked with an oval in Figure 2. The ANTENNA ((Y)) should blink
Press the START / STOP button and start the engine
Press the EXIT button on the device and disconnect the device from the diagnostic connector
ADD (additional key add function)
Connect the diagnostic cable to the device
Connect the device to the OBD diagnostic socket at the driver’s feet
Press and release the START / STOP button or press and release the brake pedal to “wake up” the car electronics
In the device menu, select ADD
If you see TRAINING … wait until the training is over, about 1-2 minutes
If you see RISE TO BUTTON – press the brake pedal and touch the device to the START / STOP button, with the back cover as marked with an oval in Figure 2. The ANTENNA ((Y)) should blink.
You will hear one beep, remove the device from the button and apply a programmable key to the START / STOP button, you will hear a beep confirming the programming of a new key.
Press the EXIT button on the device and disconnect the device from the diagnostic connector
Errors and solutions
In case of an error message (ERROR), check the diagnostic connector, make sure that the machine “woke up” and try again.
If during the operation of the CONNECTION function there are errors, it is possible that there is a key to this car in the car. Remove it or remove the battery from it.
If the ADD function is unable to add the key, the key may not be new or it may not be suitable for the vehicle. Erase the key using
Cars with A9 keys
RX (from 09.2015)
LC200 (since 2016)
LX570 (from 2016)
PRIUS (since 2016)
C-HR etc.
For some of these models, the Central Gateway module, when armed, blocks access via the diagnostic bus. There are alternative connections to the SMART unit to bypass the blockage. To connect to the CAN bus, use the NEEDLE cable, the OBD cable must be connected to the OBD connector of the car.
Description
Device for disarming and starting the Toyota \ Lexus 2008-2017 engine
The device allows you to start Toyota / Lexus engines for 10 seconds with the smart key system in May 2017. You just need to connect the device to the OBD2 connector or, in the second option, to the car’s CAN bus. The device is automatically triggered after such a connection, therefore, to start the engine, it is enough to select the appropriate item in the menu and bring the device to the START \ STOP button and press it.
Almost all Toyota / Lexus models with KEYLESS-GO system covered (2008 -2017)
The device unlocks smart modules and programs smart keys with chips: D4 / 94/98/88 / A8 / A9
To unlock and program, you only need to connect the device to the OBD 2 connector of the car
Smart key programming takes up to 5 minutes
Инструкция:
Reviews
There are no reviews yet.